Remove the battery with gloves and clean the battery compartment with a toothbrush and vinegar. After drying, new batteries can be inserted into the device. Is the manual of the Spektrum DX6 available in English? Unfortunately, we do not have the manual for the Spektrum DX6 available in English. This manual is available in English. Remote Controller. ACRO Mixing HELI Helicopter Swash Type Collective Type Pitch Curve Tail Curve Sail sailplane Camber Preset Camber System SAIL Mixing V-Tail Differential Mechanical Conversion Adjust Throttle Friction Straps FCC Information IC Information FAA Information European Union Failure to exercise caution while using this product and comply with the following warnings could result in product malfunction, electrical issues, excessive heat, FIRE, and ultimately injury and property damage.
The transmitter comes with a thin, clear plastic film applied to some front panels for protection during shipping. Humidity and use may cause this film to come off. Carefully remove this film as desired. Digital Battery Voltage an alarm sounds and the screen flashes. D when battery charge gets down to 4. Press the scroll wheel to make a selection. Anytime the transmitter power is on, press the Clear and Back buttons to access the Model Select screen.
No radio transmission occurs when a System Setup screen is displayed, preventing accidental damage to linkages and servos during changes to programming. Press the scroll wheel once to display the Function List. Rolling and clicking the scroll wheel turns the selected box black, indicating that the value or condition will act on that position.
To easily select a switch in a function, such as a program mix, roll with the scroll wheel to highlight the switch selection box, and press the scroll wheel. The box around the switch should now flash. To select a switch, toggle the switch you wish to select.
Verify the switch selection is now displayed as desired. When correct, press the scroll wheel to select this switch and complete the switch selection. Power off the transmitter. Press the SD Card into the card slot with the card label facing the back of the transmitter.
The card is keyed to fit in the case in only 1 direction. Do not use excessive force to install. Exporting the transmitter serial number to the SD Card allows you to copy and paste the serial number into the registration screen at spektrumrc. Press and hold the scroll wheel while powering the transmitter on until the System Setup list appears. Scroll to the System Settings menu.
Press the scroll wheel once to open the menu. Power off the transmitter and remove the SD Card from the transmitter. Insert the SD Card in your computer and open the. Never power off the transmitter when updates are installing.
Doing so may damage the system files. The update may erase all model files. For more information on AirWare software updates, visit spektrumrc. Download the update from spektrumrc. Power off the transmitter and install the SD Card in the transmitter. Power on the transmitter and the update automatically installs in the transmitter.
The Select File screen appears. Select the desired AirWare version from the File List. When updates are installing, the transmitter screen is dark. The orange LED Spektrum bars flash and the update status bar appears on the screen.
Doing so will damage the transmitter. You must bind the AR receiver to your transmitter before it will operate. The screen also provides binding information. Remove the bind plug from the receiver. While pressing the Bind button, power on the transmitter. This indicates the receiver is bound to the transmitter. The transmitter screen also provides binding information. Inadequate power systems that do not provide the necessary minimum voltage to the receiver during flight have become the number one cause of in-flight failures.
Some of the power system components that affect the ability to properly deliver adequate power include:. The AR has a minimum operational voltage of 3.
If you are using a questionable power system, e. Connect the voltmeter to an open channel port in the receiver and, with the system on, load the control surfaces apply pressure with your hand while monitoring the voltage at the receiver. The voltage should remain above 4. Ni-MH batteries charged with peak detection fast chargers have a tendency to false peak i.
This interrupts control, as the servos and receiver require a minimum of 3. QuickConnect with Brownout Detection is designed to allow you to fly safely through most short duration power interruptions. Replacement Antenna: DX6i. Aircraft Telemetry High-Current Sensor. NX6 6 Channel Transmitter Only. Wireless Simulator Dongle WS DX10t Function Module L1. DX10t Function Module R1.
A Digital Aircraft Servo. Nanolite High Speed Heli Servo. STi iTelemetry Interface. Aircraft Telemetry Airspeed Indicator.
MR Marine 2. DXS Transmitter Only. DX6e 6 Channel Transmitter Only. WaterResist 25mw 5. Nitro Telemetry Combo Pack. The transmitter assigns the trainer function to Switch I. Page Wireless Trainer Secondary functions can be individually assigned to the Slave transmitter as necessary. It is not necessary to have model programming in the slave transmitter.
Page System Settings 2. Scroll to the battery voltage and press the scroll wheel. Press the scroll wheel again to save the selection. Inhibit removes all trim bars and indicators from the Main Screen. Register your DX6 to get AirWare software updates and other news at spektrumrc. Ensure that the Page Update Airware Software 6. Before updating the sound files, make sure the transmitter battery is fully charged. Failure to do so will result in the throttle moving to full throttle if failsafe activates.
Move the Throttle stick until the cursor is near the point you wish to remove. Scroll to Remove Pt. Page Mixing If you wish to assign a mix to a switch position: 1. Make sure you are in the desired mix screen. Move the switch you want to assign the mix to.
Scroll to the switch position where you want the mix to be active. Press the scroll wheel to activate the mix. When the box is filled, the mix is active. You can assign a mix to be active in multiple switch positions 0,1 or 2.
An alarm sounds when the programmed time is reached. You can Page Telemetry A variety of alerts can be chosen from the list, including telemetry alerts and a variety of flight conditions and commands. This is useful to verify programming functions, trim settings, mix directions, etc. The numeric value is directly relative to the travel adjust and mix values e.
0コメント