Yamaha fz6 parts manual

Click here to download your FZ6 NS owners manual. Click here to download your FZ6 NT owners manual. Click here to download your FZ1 NW owners manual. Click here to download your FZ1 SW owners manual. Click here to download your FZ1 NX owners manual.

Click here to download your FZ1 SX owners manual. Click here to download your FZ1 NY owners manual. Click here to download your FZ1 SY owners manual.

Click here to download your FZ1 NZ owners manual. Click here to download your FZ1 SZ owners manual. Click here to download your FZ1 NA owners manual. Click here to download your FZ1 NB owners manual. Click here to download your FZ8 SB owners manual.

Your email address will not be published. Skip to content About. Pingback: There are 2 electrical wires going to the throttle twistgrip - SuccessAsk. S When checking the wire harness, perform steps 1 to 3. S As a quick remedy, use a contact revitalizer available at most part stores. The following special tools are necessary for complete and accurate tune-up and assembly. Use only the appropriate special tools as this will help prevent damage caused by the use of inappropriate tools or improvised techniques.

Special tools, part numbers or both may differ depending on the country. When placing an order, refer to the list provided below to avoid any mistakes. S For U. This chart specifies tightening torques for standard fasteners with a standard ISO thread pitch. Tightening torque specifications for special components or assemblies are provided for each chapter of this manual.

To avoid warpage, tighten multi-fastener assemblies in a crisscross pattern and progressive stages until the specified tightening torque is reached. Unless otherwise specified, tightening torque specifications require clean, dry threads.

Components should be at room temperature. First, tighten the bolts to approximately 12 Nm 1. Following the tightening order. Retighten the bolts 25 Nm 2. Loosen the all bolts one by one following the tightening order and then tighten them to 27 Nm 2. First, tighten the ring nut to approximately 52 Nm 5.

Retighten the lower ring nut to specification. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password.

First edition, August All rights reserved. Illustration is for reference only. TRIP 1! TRIP 2! TRIP F! ODO When approximately 3. Tachometer mode Displays the digital indication of the engine speed on the odometer section. During reassembly, properly oil all mating grease parts and bearings and lubricate the oil seal lips with grease. Tool No. YM Sheave holder This tool is used to hold the generator rotor YSA when removing or installing the generator ro- tor bolt or pickup coil rotor bolt.

Piston pin puller YU This tool is used to remove the piston pins. Radiator cap Radiator cap tester tester Adapter YU Adapter These tools are used to check the cooling system. YU Steering nut wrench YU This tool is used to loosen or tighten the steer- ing stem ring nuts. Damper rod holder 1 1 T-handle 2 These tool are used for holding the damper rod when removing or installing the damper rod. Pivot shaft Pivot shaft wrench wrench Pivot shaft wrench adapter YM Pivot shaft wrench This tool is used to loosen or tighten the pivot adapter adjust bolt and engine mount adjust bolt.

Compression Compression gauge gauge Adapter YU These tools are used to measure engine Adapter compression. Pocket tester YU This tool is used to check the electrical sys- tem. Oil pressure Oil pressure gauge gauge Adapter YU These tools are used to measure engine oil Adapter pressure. Fuel pressure adapter YM This tool is needed to measure fuel pressure. Pressure gauge YU This tool used is to measure fuel pressure. Piston ring compressor YM This tool is used to compress piston rings when installing the cylinder.

Valve spring Valve spring compressor compressor Attachment YM Attachment These tools are used to remove or install the valve assemblies. YM Clutch holding tool This tool is used to hold the clutch boss YM when removing or installing the clutch boss nut. In , the headquarters was moved to Iwata.

In , the first Yamaha arc welding robot was introduced. By the end of the s, having mastered the US motorcycle market, the Yamaha Motor Company ranked second in the world for their production. In , the company made an attempt to oust Honda from the first place, having begun mass production of new models. Competitors answered in the same way, and Harley Davidson managed to impose restrictive tariffs on imports of Japanese motorcycles in the USA.

Since , Yamaha Motor began operations in India. There are two factories in India. In , the Yamaha Motor Company began a partnership with the Italian motorcycle manufacturer Minarelli, in the company became part of the Yamaha Motor. In , Yamaha and the Italian sports car brand Abarth entered into a partnership agreement for the 2 seasons of the MotoGP World Championship and DanielCharron Tuesday, 12 October Hello, I need a shopmanualfor a yamaha XT Can you help me tofind it.

Tank you for the answer Best regard Daniel My email are dandidikk hotmail. Muhammad Zeeshan Monday, 28 June Dear sir, I need YBZ complete manual please. Can your help. Dan Collins jr Friday, 28 May PDF Wiring Diagrams. Parts Catalogues. History of the Yamaha Motor.

Yamaha Fazer Comments: 3.